Stingray

If it does, is there some tip to configure a i810 motherboard to accept a second video card (PCI, of course) ?

Ok.. it worked fine on an Intel BX motherboard.. seems the problem is some incompatibility with the i810 chipset then, that has AGP video card on-board.

I am using RC2 with dual monitors and two video cards, but my taksbar stays only in one monitor. (I had NT4 before, and the same config, and the task bar occupied the two monitors). Any help ??

PLZ HELP ! I have the following config: Abit BP6 Dual Celeron 366 Win 2k 2114 pro Voodoo3 2000 HD Quantum Fireball Plus KA I installed Win2k, it works fine with the two processors but I have two problems: - I installed the Voodoo3 drivers downloaded from here, and followed all the instructions, in 2D it is perfect, but Direct3D and Glide don't work in any game, I can run only Quake 2 and 3. I looked for the registry entry (CapabilityOverride) to enable Direct3D but the key was not found. - I can't boot when the HD is attached to the UDMA/66 controller. I upgraded my bios to the Beta version, and installed the new drivers. Any help would be appreciated !

PLZ HELP ! I have the following config: Abit BP6 Dual Celeron 366 Win 2k 2114 pro Voodoo3 2000 HD Quantum Fireball Plus KA I installed Win2k, it works fine with the two processors but I have two problems: - I installed the Voodoo3 drivers downloaded from here, and followed all the instructions, in 2D it is perfect, but Direct3D and Glide don't work in any game, I can run only Quake 2 and 3. I looked for the registry entry (CapabilityOverride) to enable Direct3D but the key was not found. - I can't boot when the HD is attached to the UDMA/66 controller. I upgraded my bios to the Beta version, and installed the new drivers. Any help would be appreciated !

I checked it all, everything is fine.. I give up, will go back to Win98SE until RC2 comes out..

HackNight.. I am having a problem different from you.. I can run Direct 3D and OpenGL games, but I can't run no Glide games.. what drivers you installed for your V3 ?? (I am using build 2114)

My desktop is set to 16bits.. I don't understand.. I thought Glide was easier to run then Direct 3D... Anybody there can run Glide games in W2k with a voodoo3 board ?

SHS, The ATA/66 problem was solved with new drivers and BIOS from HPPT.. now boots and runs fine in the ATA/66 controller ! YES ! About DirectX.. The tab D3D was gray out.. I find somewhere in the Net a Direct X7 RC4 for win2k, I installed it and the tab appeared, I ran both software render and hardware D3D test and passed fine. Now some D3D games run fine (e.g. C&C Tiberian Sun), but Fifa99 don't run even in Software Render mode... About Glide games, (I installed with the drivers recommended in the INF and Voodoo3.dll and Voodoo3.sys from drivers.cab of my win2k installation), many games recognize Voodoo3 (e.g. Carmagedon 2), but when I try to run, I get the 3dfx logo and after that, it returns to my windows desktop. Some games (like Fifa 99) don't recognize Voodoo3 (in 3dsetup, I get a lot of errors and then I have the options of Direct3D Device 1 and Software Render). About the "CapabilityOverride" key, I searched all the registry and couldn't find it. Quake 3 works fine. But if I try SMP mode it hangs. I guess thing are a lot better now and I am almost upgrading all my stuff for Win2k.. I just need my Glide games running now..