RoGuE

first if you want the speeds im getting over isdn you need to throw the isdn modem in trash and get a router....i have found good routers at ebay for real reasonable prices. And as far as the firmware update goes...i hope you saved the firmware that was in your t/a before, cause i would suggest going back to the firmware that worked.....i had an adtran 3000 connected to my computer before{isdn modem} and my download speeds sucked. the reason is the shortcomings of using a com port versus a nic card....when you use a com port you take a 20k a sec hit right off the bat because the fastest your com will run is 115k..and its like a 56k modem for the fact that your connection speed could be slow too. with the router i connect at true 128k and can use compression which jumps me too 230k....my downloads before were at a snails pace{5k to 10k} now the slowest i get is 18k. so if your looking for speed on isdn get rid of the old isdn t/a, modem and get ya a router. also you have to be carefull and dont make the same mistake i did, get a router that will support dynamically assigned ip addresses from your isp. you can contact me on icq and i can help ya find a good one......

A3D is a 3 dimensional software driver in the diamond multimedia based sound cards....eax is the 3d driver for live!, there is no support for eax in Quake3A at this time.....sorry

try installing the liveware first with the liveware 3 and use the updated drivers later. follow his directions to the letter or it wont work. believe me it took me 2 times to get it right. if you need further help just get ahold of me on icq{18411966} and ill help ya all i can..my live is working perfect and i have 4 speaker support.

i followed instructions that were posted on this site....this site rocks!! also id like to thank everyone who has helped me with my compatibility problems while changing to this os. ive had numerous problems and thanks to the comprehensive advice and the HUGE amount of knowledge at this site i have gone to win2k fairly smoothly. all games and hardware work perfectly now. thanks again RoGuE

i recently purchased a ALR autobahn isdn router....it says to use a communication proggy with vt-100 emulation to configure it. when i connect to the router all i get is a window with characters scrolling across it...im using hyper terminal to access it. if there are any networking guru's in the group id really appreciate the help...this is my first attempt at configuring a router and i must have something configured wrong in hyper terminal to have it giving me this window....it should come up with a configuration menu...any help would be much appreciated.

i bought a zyxel prestige 128u. its works flawlessly. perfect. also, my download speeds before sucked now im ripping along a 27 to 50k{sometimes} a second....the problem was i was trying to use routers that didnt support dhcp with a isp that assigns dynamic ip addresses....thanks for the help guys

no the drop menu comes down...but i dont have any sound. then the computer hangs when its booting up....cant load the live menu. then if i uninstall the liveware 3.0 and reboot into safe mode and re run the run.cmd i get sound back....i dont have 4 speaker support and i have sound but its got a lot of reverb in it....

has anyone found a tnt tweak program.....to adjust gamma, overclocking, and such settings just wondering....i really miss being able to tweak out my nvidia card

and oh yeah, is there newer revised instructios besides? im using the instructions found on this site

well ive gone through tne instructions several times and all ive managed to do is get sound....i dont have a modem {internet behind a zyxel isdn router} and i get stuck on step #3.....if you can help me with this give me a jingle at quakin@swbell.net

well i gave up on that router and now i have anoter one...but this one doesnt support dhcp...so now ive got to get ANOTHER router....thanks for the help but i guess that router was defective because ive done everthing the manual and you guys have told me to do. im assuming that the firmware chip is blown or something

yes they are both db9. the guy at radio shack told me that there is no difference between RS-232C and the RS-232, so im at a loss here

oh. and yes you were correct on the stop,start bits and the baud rate....

the only thing i can figure is that the serial cable i bought at radio shack is mislabeled...is there a difference between RS-232 and RS-232C cables? the bood says that i need a RS-232 and i bought a RS-232C...maybe thats the problem.

well i tried the special characters and no go...i guess since this router is used it wont let me access the setup menu.....im dl another communication proggy to try again with it....

okay the vt-100j didnt work either....im sure its something that im overlooking....

ill try the vt-100j but it specifically says to use vt-100....my buddy thinks that the router is defective but im not convinced that it is...it boots up and all the lights come on without any errors...it is used though...so maybe the previous settings are interfering with the setup screen...dont know to much about em.

SUCCESS!!!! I was having hell with my tnt2 card and the driver that i got from chameleon's site has eliminated the problems...now its time to conquer the creative live! value....thanks a million p.s. rc3 rocks..thanks again!

IVE GOT A PROGRAM CALLED Q3TWEAK....THIS PROGRAM WILL LET YOU ADJUST YOUR GAMMA AND IT WORKS GREAT WITH WIN2K....JUST GET AHOLD OF ME ON ICQ OR EMAIL AND ILL SEND IT TO YA...

I have gone to great lengthes to get my creative to work on build 2031. I finally got my new drivers everything installed fine, but now i get this message when I try to play a movie: Analog copy protection violation: Windows cannot play this copy-protected disc because it cannot verify that the video outputs on your DVD and/or VGA cards support copy protection. Possible causes: (1)One of the drivers (DVD or VGA) does not fully support the adapters capabilities, in which cas installing an updated driver may help; (2)The hardware does not support copy protection. You may be able to get around the problem by unplugging any cables connected to the video outputs on your computer. Otherwise please contact your system manufacturer. Does anyone know what in the world this means..im running a creative tnt2 value vid card with a 5x dxr2 dvd drive....cant figure it out..wont even let me play movies on my puter

im using a hardware decoder cause i have it all tied into my home entertainment sys....i record movies to vhs. ive got rc3 now...THANKS CHAMELEON!! and im hoping it will fix a lot of the probs...ive got to deal with my live value next...im dreading it

i had the same prob with my vid card {creative tnt2 value} and i used the 3.53 driver and still couldnt control the gamma. the advanced control applet isnt there like it is in the creative drivers so i went back to them....the problem with these drivers are that they wont allow me to use my dvd player....get a copy write error...cant figure it out.

well everytime i try to install the new tnt2 drives it screws my machine up.....wont even boot...gotta go in safe mode and change the crap back....im trying to get a copy of win2k rc3 but it seems the guys who have it are a little tight lipped with it....anyway, im running the beta3 {build 2031} so thats pobably the prob....sucks!!!!

i have a creative graphics blaster tnt2 value...{kinda like the live value} anyway, my vid card works great. i install the drivers for nt off the setup disk and then use the latest wdm drivers from creative....you can get these drivers from www.creative.com. ive found if you use the drivers posted from these boards that there is no opengl or d3d in them. i can play all my favorite games but unreal and unreal tourney. all quake engine games run better for me in win2k. if you cant find the drivers at creative ive got em and you can reach me by icq# 18411966.

im running an old build{2031}. quake 3 runs excellent, as a matter of fact all quake engine games run great. but as soon as i try to run a game such as unreal or any other no quake engine game i goes to windowed mode with only half of the screen showing in it....if i try to use the updated tnt2 drivers i lose all open gl capabilities. i dont understand whats happening there. im upgrading to rc2 this week. im running a creative grapics blaster tnt2 value....its a 16 meg card. i run quake at 1024X728 at 75 fps, so im not complaining.