Very LONG post about my very FRUSTRATING problem (Win2K &amp

[Ythan 0]

Hey everybody... I've been having a big problem with my system which has me completely stumped. I've been trying to fix it for months now and it's my hope that someone will be able to offer some insight into what might be going wrong.

 

This is my rig. In a nutshell, here's my problem: I have a Maxtor 15GB 7200RPM drive which I'm using as my boot drive (it's a 51536H2 if anyone's wondering). I also have four Maxtor 60GB 7200RPM drives (T060H6) which I have set up as a stripe set using Windows 2000's software RAID. The boot drive is connected to my onboard IDE controller, and the 60 gigs are hooked up to two Promise ATA 100 controller cards, with each drive on its own channel.

 

I'll partition and format one big volume across all my disks. It will works great initially... I can install and run programs from it, it's really fast, and it seems stable. But after running it for a couple of days, and installing most of my programs, it gets flakey. I'll start getting weird error messages in my programs, and when I run a disk check it will find hundreds of disk errors. At first, it will fix these errors and my system will work okay for another day or so. Eventually I'll be using my computer and I'll get one final error message. Usually I'll be playing some game like UT or Serious Sam and it will crash out between levels. Sometimes, though, it would happen overnight, when I'm not touching my computer, presumably while Diskeeper is running its scheduled defrag but I'm not really sure. I have to reboot my computer, and when it comes up again, my 229GB volume now shows up as being 0 bytes.

 

Disk administrator under computer management shows the volume as being healthy, but all my data is gone. There's no way to easily recover it as far as I can tell. This has happened to me with probably a dozen clean installs. Here's some history so you know what I've tried already to fix it.

 

Originally, I had an 800MHz coppermine running on a Tyan Trinity 400 motherboard. I think I had 384 megs of Micron PC133. I was using a Radeon 64MB ViVo as my primary video card, and the PCI Voodoo 3 as my secondary card. I had a SoundBlaster Live 5.1 and a Linksys NIC. I had a 10GB boot drive and two 15GB drives set up in a stripe set. The 10GB was hooked up to my motherboard, the 15GBs to one of the Promise ATA 100 cards.

 

I started having the problem exactly as I described above, only with the two 15GB drives. My volume would get corrupted, and eventually vanish. I installed all the latest patches, drivers, firmware for the ATA card, chipset drivers from VIA, etc. Still had the exact same problem. Thinking it might be hardware related, I decided to swap out some parts. Over the course of a month or so, I replaced virtually everything in the system.

 

I got a 1GHz coppermine instead of the 800, in case it was a problem with the CPU. I replaced my Radeon with a GeForce3. I got the four 60GB drives, so I used them as my stripe set and used one of my old 15GB drives as my boot drive. I got two brand new Promise controller cards and got rid of the old one I had been using. I exchanged my SoundBlaster Live for a new one. I replaced my Linksys NIC with a Realtek. I got rid of my Micron RAM and replaced it with two 256MB sticks of Infineon PC133 2-2-2. Because of the problems I read about people having with the SBLive and the VIA VT82C694X & VT82C596B north & southbridges, I decided to try a new motherboard. I picked up the Soyo SY-7IS2, which is based off the Intel 815EP chipset.

 

Guess what? Same problem. I'm installing Windows 2000 off a CD with SP2 already slipstreamed in. My hardware is pretty different and almost all the drivers I'm using are new or updated from when I first started having this problem. All sorts of critical updates and whatnot. Nothing fixes it. I tried turning the hardware acceleration on my SBLive off and that didn't solve anything, so I pulled it out and tried using a SoundBlaster 16 and some generic Aureal A3D card, but no love. I tried using some SiS PCI graphics card instead of the Voodoo 3 for a little while, but that didn't fix anything so I went back to the Voodoo which can do higher resolutions.

 

It's really hard to tell exactly what is causing this to start happening. It doesn't occur unil I've been using my computer for a little while, and I don't really use my computer much until I have all my drivers and programs installed. I've observed that I never get any sort of data corruption on my 15GB. The stripe sets I've created have always been with drives hooked up to a Promise controller card. I haven't tried hooking the drives up to my motherboard, since that wouldn't be practical for my current setup so I don't care whether it would fix the problem or not. In a little bit I'm going to ditch the Promise cards and get an Adaptec 2400A IDE RAID controller to see if that helps, but since I'm stuck with my current setup for the time being I'd like to get it working if possible.

 

There are a few things which I think could be causing this problem. One is the Promise cards. They've been a constant the whole time I've been experiencing these issues with my computer. I know it's not a hardware problem with the cards, since I got them brand new. It's also not a compatibility issue between the ATA cards and my chipset, since I've tried two different motherboards. It could be a conflict with one of the other cards in my system, but I've replaced every single one of them at some point. I'm inclined to think that if it is a conflict with another card, it's with "the PCI video card" or "the sound card", not with a particular card from a particular manufacturer. One thing to note is that I have 8 different devices all sharing IRQ 11, including my two video cards, my two ATA cards, my NIC, and my SBLive. From what I understand this shouldn't be a problem under Windows 2000 with a 100% ACPI compliant motherboard, but it's still kind of weird to see.

 

I haven't tried taking out my secondary video card or my sound card completely, since I need both of them. I don't think there's problem with using two ATA cards, since I had the same problem back when I was only using one. Also, the Promise cards handle it very elegantly... during boot when the ATA card it detecting drives, it shows drives 0 through 7, instead of showing the card's BIOS twice with 0 - 3 each time.

 

My system event log has one slightly odd warning in it. Every 60 minutes (to the second) after booting my computer, I'll get this warning twice, 1 second apart:

 

Event Type: Warning

Event Source: Ultra

Event Category: None

Event ID: 26

User: N/A

Description:

The description for Event ID ( 26 ) in Source ( Ultra ) cannot be found. The local computer may not have the necessary registry information or message DLL files to display messages from a remote computer. The following information is part of the event: \Device\Scsi\Ultra1.

 

I'm pretty sure it's unrelated, since this error is widely reported on the usenet and doesn't appear to be associated with data corruption on anybody else's system. Still, I figured it was worth mentioning.

 

Anyway, if you're still reading this, I appreciate you taking the time to see if you can offer any help... I'd be very grateful for any suggestions or feedback since I've been fighting with this stupid machine for way too long. Thanks in advance for any insight anyone can offer into this mysterious problem I'm having with my computer.

 

-Y

[CrazyKillerMan 0]

Heh...raid = pain in the ***.

I had a sorta similar problem with an IWILL Side RAID 100 and 2 maxtor 30 gig, 7200rpm ata100 drives. The problem was that fdisk and the 2k install could see the drives no problem, but, after initial instalation, when the computer reboots, its sticks at the starting windows screen. Believe you me, there was NO way to get ide raid working.

The problem I had, was as you mention, sharing or irq's. It was sharing the irq with nic(also linksys), soundcard(also sblive) and some other crap like the serial stuff or something, cant member.

So...I ditched the iwill card and got the promise fastrak 100.

BAM...no longer does the raid card share irq's, worked the first time on install and I have been running now for about a month with no data corruption. So its not the fast trak 100.

 

Why do you have 2? Why not use one fast trak with all four drives attached (this config can still be striped), I cant see this config to be of any use, using the 2 raid cards, as you will not see any speed increase. I hammer out 46000 in sandra with my setup, and that is plenty fast.